Boss PSA-230S2 Netzteil 9V 500mA

Der EHX 9.6VDC-200mA Power Adapter ist die erste Wahl für viele der beliebtesten Gitarreneffektpedale der Welt, um diese statt einer 9 Volt Block-Batterie zu betreiben. Es liefert eine linear geregelt Stromversorgung.SpezifikationenStromdaten: 9,6 Volt DC, 200 mA2-Pin EurosteckerAusgang: 5,5 / 2,1 mmm HohlsteckerPolarität: Center MinusAbmessungen: 7,6 x 4,8 x 6,4 cm

CIOKS 8 ExpanderThe largest power supply extender in the Future Power Generation seriesWhen the celebrated CIOKS DC7 was released, it definitely caused a stir in the PSU market. With its ground-breaking low profile, low weight and high output connectivity, DC7 has quite rightly found its way onto thousands of pedalboards the world over. Now with the CIOKS 8 Expander, the range has increased to provide pedal devotees even more low noise power options for their sonic treasures.CIOKS 8 is our largest switch-mode power supply extender. Not only is CIOKS 8 the perfect companion to the CIOKS DC7 (via the DC7s 24 V outlet), but it can also be used and offer clean power from other PSUs that has a 24 V DC outlet.With its eight additional outlets, individually selectable between 9, 12, 15 and 18V DC, each outlet can deliver up to a staggering 660 mA! To use CIOKS 8 as an extension to DC7, simply use the included DC Link cable to connect the CIOKS 8 to the courtesy 24V outlet on your DC7 and you are good to go. In case you want to use CIOKS 8 as a stand-alone power supply you can power it with any 24V DC adapter with the appropriate DC plug. To get the full 6W output power on all 8 isolated outlets, the adapter used to power CIOKS 8 should have an output power of 60W.If you are looking for a super powerful power supply setup to power a large pedalboard, the combination of a CIOKS DC7 plus a CIOKS 8 will definitely be a stunning solution, as this combo will give you 15 isolated outlets in total with 4 switchable voltages on each outlet plus a 5V USB outlet to charge your smartphone or tablet (courtesy of DC7).Main Features:" Ground-breaking low profile and weight" 8 isolated DC-outlets, each providing up to 660 mA (at 9 V DC) - total maximum output power 48 W*" Ultra-low noise achieved by multi-stage filtering" Independently selectable voltage on each outlet (9, 12, 15 or 18 V)" Global overload status LED" Mounting hardware for Pedaltrain and Templeaudio boards included" Compatible with CIOKS GRIP - for drill-free mounting on Pedaltrain boards" 24 V DC link and 12x Flex cables included:    (1x 1015 3x 1030 2x 1x 2050 1x 4050 1x 5050 1x 1035 & 1x 1533)" Designed in Denmark, assembled in Poland" 5-year worldwide warrantyCIOKS 8 Expander KitThe largest power supply extender in the Future Power Generation seriesWhen the celebrated CIOKS DC7 was released, it definitely caused a stir in the PSU market. With its ground-breaking low profile, low weight and high output connectivity, DC7 has quite rightly found its way onto thousands of pedalboards the world over. Now with the CIOKS 8 Expander, the range has increased to provide pedal devotees even more low noise power options for their sonic treasures.CIOKS 8 is our largest switch-mode power supply extender. Not only is CIOKS 8 the perfect companion to the CIOKS DC7 (via the DC7s 24 V outlet), but it can also be used and offer clean power from other PSUs that has a 24 V DC outlet.With its eight additional outlets, individually selectable between 9, 12, 15 and 18V DC, each outlet can deliver up to a staggering 660 mA! To use CIOKS 8 as an extension to DC7, simply use the included DC Link cable to connect the CIOKS 8 to the courtesy 24V outlet on your DC7 and you are good to go. In case you want to use CIOKS 8 as a stand-alone power supply you can power it with any 24V DC adapter with the appropriate DC plug. To get the full 6W output power on all 8 isolated outlets, the adapter used to power CIOKS 8 should have an output power of 60W.If you are looking for a super powerful power supply setup to power a large pedalboard, the combination of a CIOKS DC7 plus a CIOKS 8 will definitely be a stunning solution, as this combo will give you 15 isolated outlets in total with 4 switchable voltages on each outlet plus a 5V USB outlet to charge your smartphone or tablet (courtesy of DC7).Main Features:" Ground-breaking low profile and weight" 8 isolated DC-outlets, each providing up to 660 mA (at 9 V DC) - total maximum output power 48 W*" Ultra-low noise achieved by multi-stage filtering" Independently selectable voltage on each outlet (9, 12, 15 or 18 V)" Global overload status LED" Mounting hardware for Pedaltrain and Templeaudio boards included" Compatible with CIOKS GRIP - for drill-free mounting on Pedaltrain boards" 24 V DC link and 12x Flex cables included:    (1x 1015 3x 1030 2x 1x 2050 1x 4050 1x 5050 1x 1035 & 1x 1533)" Designed in Denmark, assembled in Poland" 5-year worldwide warrantySpecifications:Input/Through:     Dual 24 V DCOutlet 1-8:    9 V DC / 660 mA or        12 V DC / 500 mA or        15 V DC / 400 mA or        18 V DC / 330 mA eachOutput power:     max. 48 W in total** Total output power of 48 W can be achieved provided an appropriate and sufficient input power source is applied. For full output power please use a 24 V DC source with min. 60 W of power capability such as CIOKS DC7).Flex cables included:Total of 12 Flex cables, all 2.1mm (BOSS standard), are included. The user is able to power 11 pedals with the included Flex kit." 1x 1015  Type 1 - 5,5/2,1mm DC plug, centre negative, L-shape, 30cm (black)" 3x 1030  Type 1 - 5,5/2,1mm DC plug, centre negative, L-shape, 30cm (black)" 2x 1050  Type 1 - 5,5/2,1mm DC plug, centre negative, L-shape, 50cm (black)" 1x 2050  Type 2 - 5,5/2,1mm DC plug, centre positive, L-shape, 50cm (red)" 1x 4050  Type 4 - 5,5/2,5mm DC plug, centre positive, L-shape, 50cm (green)" 1x 5050  Type 5 - 3,5mm Jack plug, tip positive, L-shape, 50cm (black)" 1x 1035  Split Flex type 1, 30+50cm (black)" 1x 1533  3-way daisy chain Flex type 1, 30-30-50cm (black)Specifications:CIOKS 8 Expander KitThe largest power supply extender in the Future Power Generation seriesWhen the celebrated CIOKS DC7 was released, it definitely caused a stir in the PSU market. With its ground-breaking low profile, low weight and high output connectivity, DC7 has quite rightly found its way onto thousands of pedalboards the world over. Now with the CIOKS 8 Expander, the range has increased to provide pedal devotees even more low noise power options for their sonic treasures.CIOKS 8 is our largest switch-mode power supply extender. Not only is CIOKS 8 the perfect companion to the CIOKS DC7 (via the DC7s 24 V outlet), but it can also be used and offer clean power from other PSUs that has a 24 V DC outlet.With its eight additional outlets, individually selectable between 9, 12, 15 and 18V DC, each outlet can deliver up to a staggering 660 mA! To use CIOKS 8 as an extension to DC7, simply use the included DC Link cable to connect the CIOKS 8 to the courtesy 24V outlet on your DC7 and you are good to go. In case you want to use CIOKS 8 as a stand-alone power supply you can power it with any 24V DC adapter with the appropriate DC plug. To get the full 6W output power on all 8 isolated outlets, the adapter used to power CIOKS 8 should have an output power of 60W.If you are looking for a super powerful power supply setup to power a large pedalboard, the combination of a CIOKS DC7 plus a CIOKS 8 will definitely be a stunning solution, as this combo will give you 15 isolated outlets in total with 4 switchable voltages on each outlet plus a 5V USB outlet to charge your smartphone or tablet (courtesy of DC7).Main Features:" Ground-breaking low profile and weight" 8 isolated DC-outlets, each providing up to 660 mA (at 9 V DC) - total maximum output power 48 W*" Ultra-low noise achieved by multi-stage filtering" Independently selectable voltage on each outlet (9, 12, 15 or 18 V)" Global overload status LED" Mounting hardware for Pedaltrain and Templeaudio boards included" Compatible with CIOKS GRIP - for drill-free mounting on Pedaltrain boards" 24 V DC link and 12x Flex cables included:    (1x 1015 3x 1030 2x 1x 2050 1x 4050 1x 5050 1x 1035 & 1x 1533)" Designed in Denmark, assembled in Poland" 5-year worldwide warrantySpecifications:Input/Through:     Dual 24 V DCOutlet 1-8:    9 V DC / 660 mA or        12 V DC / 500 mA or        15 V DC / 400 mA or        18 V DC / 330 mA eachOutput power:     max. 48 W in total** Total output power of 48 W can be achieved provided an appropriate and sufficient input power source is applied. For full output power please use a 24 V DC source with min. 60 W of power capability such as CIOKS DC7).Flex cables included:Total of 12 Flex cables, all 2.1mm (BOSS standard), are included. The user is able to power 11 pedals with the included Flex kit." 1x 1015  Type 1 - 5,5/2,1mm DC plug, centre negative, L-shape, 30cm (black)" 3x 1030  Type 1 - 5,5/2,1mm DC plug, centre negative, L-shape, 30cm (black)" 2x 1050  Type 1 - 5,5/2,1mm DC plug, centre negative, L-shape, 50cm (black)" 1x 2050  Type 2 - 5,5/2,1mm DC plug, centre positive, L-shape, 50cm (red)" 1x 4050  Type 4 - 5,5/2,5mm DC plug, centre positive, L-shape, 50cm (green)" 1x 5050  Type 5 - 3,5mm Jack plug, tip positive, L-shape, 50cm (black)" 1x 1035  Split Flex type 1, 30+50cm (black)" 1x 1533  3-way daisy chain Flex type 1, 30-30-50cm (black) Input/Through:     Dual 24 V DCOutlet 1-8:    9 V DC / 660 mA or        12 V DC / 500 mA or        15 V DC / 400 mA or        18 V DC / 330 mA eachOutput power:     max. 48 W in total** Total output power of 48 W can be achieved provided an appropriate and sufficient input power source is applied. For full output power please use a 24 V DC source with min. 60 W of power capability such as CIOKS DC7).Flex cables included:Total of 12 Flex cables, all 2.1mm (BOSS standard), are included. The user is able to power 11 pedals with the included Flex kit." 1x 1015  Type 1 - 5,5/2,1mm DC plug, centre negative, L-shape, 30cm (black)" 3x 1030  Type 1 - 5,5/2,1mm DC plug, centre negative, L-shape, 30cm (black)" 2x 1050  Type 1 - 5,5/2,1mm DC plug, centre negative, L-shape, 50cm (black)" 1x 2050  Type 2 - 5,5/2,1mm DC plug, centre positive, L-shape, 50cm (red)" 1x 4050  Type 4 - 5,5/2,5mm DC plug, centre positive, L-shape, 50cm (green)" 1x 5050  Type 5 - 3,5mm Jack plug, tip positive, L-shape, 50cm (black)" 1x 1035  Split Flex type 1, 30+50cm (black)" 1x 1533  3-way daisy chain Flex type 1, 30-30-50cm (black) 

Cioks DC10 LinkDies ist eine professionelle Stromversorgung für Effektpedale auf dem neuesten Stand der Technik. Es liefert 2.800mA der saubersten Leistung aus seinen 10 isolierten Ausgängen mit 9 und 12V zur Verfügung. Abgesehen davon, dass es eines der leistungsstärksten Netzteile für Effektpedale auf dem Markt ist, bietet es auch einige neue fortschrittliche Funktionen. Der einstellbare Ausgang 10 versorgt Pedale mit nicht standardmäßigen Spannungen wie z.B. Tonebones mit 15V, Blackstar Dirt Pedale mit 22V, GLAB GSC-4 Controller mit 24V, alle Hochstrom 18V Pedale von Hiwatt, einige Vintage EHX und viele andere. Durch die sehr hohe Strombelastbarkeit von 800mA bei 9 oder 12V können Sie mit dieser einen Steckdose auch eines der großen Geräte wie Line 6 M9 oder M13, VOX ToneLab oder einige ältere BOSS GT-XX Prozessoren betreiben, um nur einige zu nennen.Mit dem mA-Meter können Sie die Stromaufnahme aller Ihrer Pedale messen, so dass Sie die richtige Steckdose für jedes Gerät verwenden können, ohne Strom zu "verschwenden", indem Sie z.B. ein 160mA-Pedal an eine 400mA-Steckdose anschließen, anstatt eine 200mA-Steckdose zu verwenden. Auch wenn Sie drei Pedale über unsere 3-Wege-Verkettung mit Strom versorgen möchten, können Sie deren Gesamt-MA-Wert überprüfen und sie einer Steckdose mit ausreichender Leistung zuordnen.Sollten Sie mehr Steckdosen, noch mehr Strom oder etwas AC benötigen, können Sie ein weiteres CIOKS Link Power Supply hinzufügen. Mit dem neuen DC10 Link bekommen Sie das Beste vom Besten von CIOKS.Features:10 isolated and well filtered outletsTotal output current of 2.800mAToroidal transformer with additional electromagnetic shieldAdjustable 9-24V DC outlet with mA-meter and very high current capabilityThree high current outlets each 400mATwo medium current outlets each 200mAFour 100mA outlets for standard pedalsShort circuit protection of all outletsAdvanced LED monitoring of each outlet120 or 230V mains voltage operation Courtesy AC mains outletCIOKS unique mains link featureTotal of 17 Flex cables includedCompatible with Pedaltrain and Temple A    CIOKS DC10 link power supply    Mains power cord    17 Flex cables:Type 1  black with 5,5/2,1mm centre negative DC plug x8Type 2  red with 5,5/2,1mm centre positive DC plug x1Type 4  green with 5,5/2,5mm centre positive DC plug x2Type 5  black with 3,5mm tip positive Jack plug x1Type 6  black with 9V battery clip x1Split Flex type 1  black, powers two pedals of a single outlet x13-way Daisy chain Flex type 1  black, powers three pedals of a single outlet x1Parallel adapter Flex  sand grey, adds currents of two outlets x1Series adapter Flex  white, adds voltages of two outlets x1Pedalboard mounting hardware: screws, washers, stand-offs and a hex keyManualProduct sheet (drill template)Flex guideudio pedalboards    - All pedalboard mounting hardware includedSpecifications: Outlet 1-2: 9V DC / 100mA each Outlet 3-4: 9 or 12V DC / 100mA eachOutlet 5-6: 9 or 12V DC / 200mA eachOutlet 7: 9 or 12V DC / 400mAOutlet 8-9: 9V DC / 400mA eachOutlet 10: 9-24V DC adjustable / 800-300mAfrom 800mA at 9V to 300mA at 24VSize: 217x88x42mm (excl. detachable rubber feet)Weight: 1,2kgWarranty period: 5 years worldwideWhat's in the box:    CIOKS DC10 link power supply    Mains power cord    17 Flex cables:Type 1  black with 5,5/2,1mm centre negative DC plug x8Type 2  red with 5,5/2,1mm centre positive DC plug x1Type 4  green with 5,5/2,5mm centre positive DC plug x2Type 5  black with 3,5mm tip positive Jack plug x1Type 6  black with 9V battery clip x1Split Flex type 1  black, powers two pedals of a single outlet x13-way Daisy chain Flex type 1  black, powers three pedals of a single outlet x1Parallel adapter Flex  sand grey, adds currents of two outlets x1Series adapter Flex  white, adds voltages of two outlets x1Pedalboard mounting hardware: screws, washers, stand-offs and a hex keyManual Product sheet (drill template)Flex guide

Typ 1 Flex-Kabel sind schwarz und mit einem 5,5/2,1 mm DC-Stecker ausgestattet. Dies ist der gängigste Typ, der auch als BOSS-Standard bezeichnet wird. Für die meisten Anwendungen bieten wir diesen Flex-Kabeltyp mit abgewinkeltem (L-förmigem) Stecker und einem 10mm Schaft an. Diese sind in den Kabellängen 15, 30, 50 und 80cm erhältlich. Für Pedale mit versenkten Steckdosen oder anderen speziellen Anforderungen bieten wir diesen Flex-Kabeltyp auch mit einem geraden (I-förmigen) Stecker oder mit einem längeren 12mm Schaft an, beide mit 50cm Kabellänge.

CIOKS DC7 PSU Future Power GenerationThe CIOKS DC7 is the thinnest, flexible and most unique power supply on the market today from Danish power supply specialists CIOKS. Perfect for powering a plethora of todays hungry effects pedals with clean, filtered power, it allows whatever you have on your pedalboard to perform at its best. Thanks to the pure 2-stage switch-mode technology inside, the ground-breaking DC7 also has a low one-inch (25.4mm) profile and weighs just 500 grams.The profile may be low but the power ratings are certainly not - DC7 puts out a maximum of 48 W from its 9 outlets and allows you to connect multiple high-current modern digital effects, plus provides clean and noiseless power for the fussiest of low powered analog pedals.Featuring 7 isolated DC-outlets for effect pedals each with four selectable voltages (9, 12, 15 and 18 V), all of DC7s DC outlets can put out 6 W, which at 9 V corresponds to a huge 660 mA of current. Additionally, DC7 also has a handy 5 V USB outlet and an auxiliary 24 V outlet. This allows you to further expand your power connectivity and outlet count with a CIOKS 4, as well as with other compatible 24 V DC power supplies, for even more flexibility.If you are looking for a super powerful power supply setup to power a large pedalboard, the combination of DC7 and CIOKS 4 will definitely be an outstanding solution, giving you 11 isolated outlets in total with huge current ability on tap, plus a 5V USB outlet to charge your smartphone or tablet, all in blissful silence to let your effects pedals shine their finest and without the weight and sizeof any other pedal power supply sold today.Combined with the large set of Flex cables included, CIOKS are confident in that this is the most flexible, noise-free solution on the market for powering pedalboards with a multitude of different pedals.Let the future begin!Main Features:Ground-breaking low profile and weight2-stage switch-mode power supply topologyUltra-low noise achieved by multi-stage filtering7 isolated DC-outlets, each providing up to 660 mA (at 9 V)Independently selectable DC voltage on each outlet (9, 12, 15 or 18 V)5 V USB Output (max 1A) - perfect for powering your tablet or phone24V DC auxiliary outlet (2A) - for expansion with CIOKS 4 etc. for additional isolated outputsIndividual power limit LEDs on each output, total load meter and global overload status LEDsMounting hardware for Pedaltrain and Templeaudio boards includedCompatible with CIOKS GRIP - for drill-free mounting on Pedaltrain boards12x Flex cables includedUniversal mains input voltage 90 to 265V AC.Total maximum output power 48WDesigned in Denmark, assembled in Poland5-year worldwide warrantySpecifications:Power Input:      90-265 V AC (IEC)DC Outlet 1-7:    9 V DC / 660 mA or        12 V DC / 500 mA or        15 V DC / 400 mA or        18 V DC / 330 mA each        5 V USB Output (max 1 A)5 V USB Output (max 1A)24V DC auxiliary outlet (2 A)Output power:     max. 48 W in totalFlex cables A total of twelve Flex cables are included:Standard Flex type 1  black with 5,5/2,1mm centre negative DC plug x7Standard Flex type 2  red with 5,5/2,1mm centre positive DC plug x1Standard Flex type 4  green with 5,5/2,5mm centre positive DC plug x1Standard Flex type 5  black with tip positive 3,5mm Jack plug x1Split Flex type 1  powers two pedals of a single outlet x13-way Daisy chain Flex type 1  powers three pedals of a single outlet x1

Netzteil für diverse Roland/Edirol Produkte z.B.: Edirol PCR 300, 500 und 800, Boss BCB 60 und Boss GT 10. 9V/ 2000 mA. Auch für Mehrere Fuss-Effektgeräte geeignet.

- Kabel 1m zur Versorgung mehrerer Bodenpedale mit 9Volt - Verbindet 8 Geräte miteinander, wobei eines davon das Speisegerät ist.

 

Das Chameleon ist ein vielseitiges Netzteil, dass für unterschiedlichste Pedal-Kombinationen konzipiert wurde. Feautures: - Galvansiche Trennung der Ausgänge - 6 Ausgangsbuchsen, bis zu 5 gleichzeitig - 9V DC, 12V DC, 18V DC oder 12V AC schaltbar je 300mA - Netzspannung schaltbar von 115/ 230 Volt - Kompaktes, unverwüstliches Design für den Road-Allt Mitgelieferte DC-Kabel: - 2 x 20 cm - 4 x 50 cm - 1 x 75 cm - 1 x 100 cm - 1 x DC auf Miniklinke (75cm) - 1 x Link-Kabel für 5 Geräte (75cm) - 1 x AC Kabel (rot) - 1 x AC Kabel (blau)

Typ 1 Flex-Kabel sind schwarz und mit einem 5,5/2,1 mm DC-Stecker ausgestattet. Dies ist der gängigste Typ, der auch als BOSS-Standard bezeichnet wird. Für die meisten Anwendungen bieten wir diesen Flex-Kabeltyp mit abgewinkeltem (L-förmigem) Stecker und einem 10mm Schaft an. Diese sind in den Kabellängen 15, 30, 50 und 80cm erhältlich. Für Pedale mit versenkten Steckdosen oder anderen speziellen Anforderungen bieten wir diesen Flex-Kabeltyp auch mit einem geraden (I-förmigen) Stecker oder mit einem längeren 12mm Schaft an, beide mit 50cm Kabellänge.

Supplies quiet, noise-free DC power to wide range of pedal typesTakes up less space than a candy barEquipped with five fully isolated outputs to eliminate obnoxious, gig-ending ground loop noiseFour 9V outputs with one switchable 9V/18V outputHandles both negative and positive groundsEnough current to accommodate almost any pedal, analog or digitalIncludes splitter cable to connect two pedals to a single outputLEDs let you know all your connections are solidLightweight & built like a tank The Mini Iso-Brick Power Supply supplies quiet, noise-free DC power to wide range of pedal types while taking up less space than a candy bar. Whether you need a space-saving solution for your downsized travel board or you just need to power a small, carefully curated selection of tried-and-true staples, this little box has what you need. First, lets talk outputs. The Mini Iso-Brick Power Supply has five, and each is fully isolated to eliminate obnoxious, gig-ending ground loop noise. Four of the outputs supply 9 volts of power at 300mA, while a fifth can be set to provide either 9 volts or 18 volts at 800mA depending on your needs. With a generous amount of current on tap and the ability to handle both negative and positive grounds, these outputs will accommodate almost any pedal, analog or digital. And dont let the five outputs restrict you-if you need to add an extra pedal, the Mini Iso-Brick Power Supply has you covered. It comes with a splitter cable that can be used to connect two pedals to a single output, provided they require the same voltage and you dont exceed the outputs current rating. You can do this with all of the outputs simultaneously-just purchase the extra cables to do so. Finally, troubleshooting can be a hassle on dark stages, so the Mini Iso-Brick Power Supply comes equipped with LEDs to let you know that all your connections are solid. Combine that with a lightweight housing that's built like a tank, and you can step on stage with confidence that your pedalboard will stay powered from gig to gig.